Tarmac Material - right forum? (1 Viewer)

[zblang]

I wasn't sure where to put this, but I am making a diorama with my new B-17 from K&C and am stuck with tarmac material. The base is going to be approximately 42inches by 34 inches. Most of the mats, etc are too small. My first question is will the lines of the "cement" matchup if I just use multiple ones? If not, what material can I use to make the tarmac?

 

[villagehorse]

I wasn't sure where to put this, but I am making a diorama with my new B-17 from K&C and am stuck with tarmac material. The base is going to be approximately 42inches by 34 inches. Most of the mats, etc are too small. My first question is will the lines of the "cement" matchup if I just use multiple ones? If not, what material can I use to make the tarmac?

Check the TreeFrog store on this forum site and see Build-a-Rama bases & terrains, concrete air strips are there. Robin.

 

[jazzeum]

Build A Rama can also do special orders.

 

[zblang]

Build A Rama can also do special orders.

I didn't realize this - thanks

 

[Guy]

You can also make the tarmac yourself for practically no money at all. If it is concrete you want, I am explaining how to make it in the thread " new project" in the diorama section of K&C
Hope it helps
guy

 

[Wraith]

If it's an actual tarmac finish you're after, rather than concrete sections, you could consider using abrasive paper (sand paper - different grades of grit), or you should be able to purchase spray cans of special effect grited paint from craft stores.

 

[Guy]

If it's an actual tarmac finish you're after, rather than concrete sections, you could consider using abrasive paper (sand paper - different grades of grit), or you should be able to purchase spray cans of special effect grited paint from craft stores.

For tarmac you can also use foam board; ( architect paper) take away the protecting paper.Sandpaper the whole surface with a fine grain . You can also imitate the cracks in the surface using a fine needle. Paint everything in different shades of dark grey and black
guy

 

[Mitch]

The best thing I have used to replicate tarmac and its texture is cork. you buy it in a roll and paint it up. It allows you to chip away and replicate road surfaces exactly. I use it for my bricks on buildings, churches etc and stick it to foam board.

For airfield runways I also use grunge board which, is a card based material used in crafting and just give it a rub with sandpaper and paint in correct tones. Its similar to the effect that K&C get on their foam board when they do their airfields and, its seems to gain praise.

Its also easy to use so, there is none of the issues of needing any kind of experience necessary. All you need to be able to do is stick it on a surface and add paints.

I would try these than buy some of the pre made products as its more enjoyable and, saves a lot of money
Mitch

 

[villagehorse]

Or you could just buy it from Mark Build-a-Rama and keep him in business, given his support of this forum. Robin.

 

[jazzeum]

Unless you're skilled some of the suggestions are good. However, if you're not -- like me -- BAR is best.

 

[noli-poli]

Depends what type of tarmac you want to build. Not all airfields were paved with concrete. The US Army engineers made use of PSP's (Pressed Steel Planking) to build airfields in record time and were common closer to the front. BAR came up with mats that simulate PSPs but in photographic prints. If you want to be more realistic and can afford the cost, Accurate Armor came up with 1/35 scale PSPs in pressed brass. 10 pcs @ ...Euro 11.67

http://www.accurate-armour.com/

 

[zblang]

I don't know if they'll work for what I'm thinking, but those a re very cool. I think I might purchase them for my Mustang